Rat Glutathione Peroxidase (GSH-Px) ELISA Kit

Rat Glutathione Peroxidase (GSH-Px) ELISA Kit

(Used in serum, plasma, cell culture supernatant and biological fluid)


This experiment uses the double antibody sandwich ABC-ELISA method. Coated with anti-rat GSH-Px monoclonal antibody on the enzyme plate, GSH-Px in the standard and the sample is combined with the monoclonal antibody, and biotinylated anti-rat GSH-Px is added to form an immune complex connected to the plate On the above, the horseradish peroxidase-labeled Streptavidin is combined with biotin, the substrate working solution is added, and the blue solution is finally added. Finally, the sulfuric acid is added to the stop solution. The OD value is measured at 450nm. Draw a standard curve to find the GSH-Px concentration in the specimen.

Kit composition (stored at 2-8 ° C)

Coated Wells

96 wells

Enzyme Conjugate


10 × Sample Buffer


20 × concentrated washing solution (Wash Buffer)


Standards (Standards): 4umol / bottle

2 bottles

Substrate working solution (TMB Solution)


The first antibody working solution (Biotinylated Antibody)


Stop Solution (Stop Solution)


Prepare reagents and collect blood samples

1. Collect specimens: serum, plasma (EDTA, citrate, heparin anticoagulation), cell culture supernatant, tissue homogenate, etc. as soon as possible, stored at 2-8 ℃ for 48 hours; longer time must be frozen (-20 ℃ Or -70 ℃), avoid repeated freezing and thawing.

2. Standard solution preparation: add 1ml of distilled water to mix well before use to make a solution of 4000nmol / ml. Set 8 standard tubes, and add 300ul of sample dilution to each tube. Add 300 ul of standard solution of 4000 nmol / ml to the first tube and mix it. Then aspirate 300 ul with the sampler and move to the second tube. Repeat the double dilution in this way, draw 300ul from the seventh tube and discard. The eighth tube is a blank control. 1umol = 1000nmol.

3. The 10 × specimen dilution is diluted 1:10 with distilled water (example: 1ml concentrated dilution + 9ml distilled water).

4. Washing solution: 1:20 dilution with redistilled water (example: 1ml concentrated washing solution is added with 19ml of redistilled water)

Testing procedures

1. Add sample: add 100ul of standard or sample to be tested to each well, mix the reaction plate thoroughly and place at 37 ℃ for 120 minutes.

2. Wash the plate: wash the reaction plate 4-6 times with the washing solution, and print it on the filter paper.

3. Add 100ul of the first antibody working solution to each well. The reaction plate was mixed thoroughly and then placed at 37 ° C for 60 minutes.

4. Wash board: same as above.

5. Add 100ul of enzyme-labeled antibody working solution to each well. Place the reaction plate at 37 ° C for 30 minutes.

6. Wash board: same as above.

7. Add 100ul of substrate working solution to each well, and place in a dark place at 37 ℃ for 15 minutes.

8. Add 100ul of stop solution to each well and mix well.

9. Measure absorbance at 450nm with a microplate reader within 30 minutes.

Result calculation and judgment

1. All OD values ​​should be calculated after subtracting the blank value.

2. With the standard products 2000, 1000, 500, 250, 125, 62.5, 31.2, 0nmol / ml as the abscissa, and the OD value as the ordinate, draw a graph on the coordinate paper and draw a standard curve.

3. According to the OD value of the sample, find the corresponding GSH-Px content on the graph.

Kit performance

1. Sensitivity: The minimum GSH-Px detection concentration is less than 16nmol / ml.

2. Specificity: simultaneous detection of recombinant or natural rat GSH-Px. Does not cross-react with other cytokines in rats.

3. Repeatability: The coefficient of variation within the board and the board is less than 11.3%.


1. The above standard holes and samples to be tested are recommended to be re-holes, and the standard curve should be made at the same time for each measurement.

2. The washing process is critical. Insufficient washing will lead to an increase in accuracy error and OD value.

3. After opening the slats, the remaining slats should be sealed again to keep the slats dry.

4. This kit should be stored in a 4oC refrigerator.

5. This kit is for scientific research only, not for clinical diagnosis!

Microwave popcorn paper bags produced from white greaseproof kraft paper


                                              Design:  Customized Design

                                              Size:       295mm×140mm×100mm


                                               Paper:   Food-grade Greasproof White Kraft Paper

                                               Compound Adhesive: Water-based White Adhesive PVA 

                                               Heat Seal Adhesive: PVA Water Soluble (Green)

                                               Side Seam Adhesive: Water Soluble Emulsion(White) 

                                               Ink: MWW (M/W Water Base Carbon Free) 

                                               Individual weight: 11.2g

                                               Oil resistant: â‰¥  kit11

White microwave popcorn bags

White Kraft Paper Bag

Bags For Microwave Popcorn,Microwave Bag,Popcorn Microwave,Custom Print Popcorn Bag

JINAN HUAFENG PRINTING CO., LTD , https://www.huafengpaperbag.com